/editions/2019/ncc-2019-volume-one/section-j-energy-efficiency/specification-jvb-modelling
ACT Appendix
1. Scope
This Specification contains the required modelling parameters for JV2 and JV3.
Intent
To prescribe how the modelling of the proposed and reference building is to be carried out under JV2 and JV3.
This…
/news/2024/ncc-public-comment-draft
The Public Comment Draft for the next edition of the National Construction Code is open from 1 May until 1 July 2024.
/resource/report/accessible-housing-estimated-cost-impact-proposed-changes-ncc
This updated report presents an order of cost estimate for the proposed changes to the National Construction Code of Australia (NCC) to include mandatory minimum accessible housing provisions for new Class 1a (single residential) and Class 2 (…
Acoustics impact noise comparatives of floor ceiling systems
/resource/report/acoustics-impact-noise-comparatives-floor-ceiling-systems
This paper is concerned with the introduction of new sound requirements to the BCA, Part F5. It attempts to clarify if the perfect environment of a laboratory simulates the exact performance level of the same material or system in the actual…
/resource/report/fatigue-damage-metal-battens-simulated-wind-loads
This paper investigates the fatigue performance of the battens using analysis methods applied in studying cladding fatigue. A series of tensile tests, static tests, constant amplitude cyclic tests and block cyclic load tests were conducted and the…
/ncc-2022-state-and-territory-adoption-dates
1 May 2023 marks the adoption of NCC 2022. Transition arrangements apply for some requirements. This table shows the transition and adoption dates by state and territory for NCC 2022 correct as at 22 September 2023.
Visit your jurisdiction’s…
/editions/2019-a1/ncc-2019-volume-one-amendment-1/section-h-special-use-buildings/part-h1-class-9b
Note:
Note:
Part H1 contains Deemed-to-Satisfy Provisions additional to those contained in Sections C, D and E for Class 9b buildings.
H1.1 Application of Part
NSW H1.1
(a)
The Deemed-to-Satisfy Provisions of this Part…
/editions/2019/ncc-2019-volume-one/section-h-special-use-buildings/part-h1-class-9b-buildings
Note:
Note:
Part H1 contains Deemed-to-Satisfy Provisions additional to those contained in Sections C, D and E for Class 9b buildings.
H1.1 Application of Part
NSW H1.1
(a)
The Deemed-to-Satisfy Provisions of this Part…
/editions/2016/ncc-2016-volume-one/list-amendments/list-amendments-ncc-2016-volume-one
LIST OF AMENDMENTS - NCC 2016 - VOLUME ONE
This set of notes has been prepared by the Australian Building Codes Board to assist NCC users in identifying changes incorporated in the 2016 edition of Volume One.
The notes provide a description of…
/resource/infographic/2022-residential-energy-efficiency-overview-provisions
An infographic providing more information on new residential energy efficiency provisions that apply to houses and other low rise multiple dwelling projects (Class 1 buildings) and apartment buildings (Class 2 sole-occupancy units and Class 4 parts of…
/resource/case-study/lighting-refurbishment-office-building
This Case Study outlines developing a DTS Solution for the energy efficiency of an interior lighting refurbishment for an office building. It is based on the DTS Provisions in Section J, Part J6 Artificial lighting in NCC Volume One.
The…
/editions/2016/ncc-2016-volume-one/section-f-health-and-amenity/part-f5-sound-transmission-and
PERFORMANCE REQUIREMENTS
FP5.1
Floors separating—
(a)
; or
(b)
a sole-occupancy unit from a plant room, lift shaft, stairway, public corridor, public lobby, or the like, or a part of a different classification,
must provide…
/editions/2016-a1/ncc-2016-volume-one/section-f-health-and-amenity/part-f5-sound-transmission-and
PERFORMANCE REQUIREMENTS
FP5.1
Floors separating—
(a)
; or
(b)
a sole-occupancy unit from a plant room, lift shaft, stairway, public corridor, public lobby, or the like, or a part of a different classification,
must provide…
Scoping study of condensation in residential buildings
/resource/report/scoping-study-condensation-residential-buildings
Provides an overview of condensation in residential buildings, and discussions about why condensation risk, and occurrences of condensation and mould may be increasing within current Australian residential buildings. Please note: ‘Appendix 02 - Survey…
/editions/2016/ncc-2016-volume-one/section-j-energy-efficiency/part-j6-artificial-lighting-and-power
J6.0 Deemed-to-Satisfy Provisions
(a)
Where a Deemed-to-Satisfy Solution is proposed, Performance RequirementsJP1 and JP3 are satisfied by complying with—
(i)
J0.1
to J0.3; and
(ii)
J1.1
to J1.6; and
(iii)
J2.1 to J2.5; and…
/editions/2016-a1/ncc-2016-volume-one/section-j-energy-efficiency/part-j6-artificial-lighting-and
J6.0 Deemed-to-Satisfy Provisions
(a)
Where a Deemed-to-Satisfy Solution is proposed, Performance RequirementsJP1 and JP3 are satisfied by complying with—
(i)
J0.1
to J0.3; and
(ii)
J1.1
to J1.6; and
(iii)
J2.1 to J2.5; and…
Standards Australia's latest news
/news/2019/standards-australias-latest-news
Standards Australia has entered into a new distribution agreement with Techstreet, a Clarivate Analytics company, to deliver greater access to content supporting innovation, safety and compliance in industries and communities across Australia.
/editions/2016/ncc-2016-volume-one/section-f-health-and-amenity/part-f4-light-and-ventilation-deemed
F4.0 Deemed-to-Satisfy Provisions
(a)
Where a Deemed-to-Satisfy Solution is proposed, Performance Requirements to are satisfied by complying with—
(i)
F4.1
to F4.12; and
(ii)
for farm buildings and farm sheds, Part H3.
(b)…
/editions/2016-a1/ncc-2016-volume-one/section-f-health-and-amenity/part-f4-light-and-ventilation
F4.0 Deemed-to-Satisfy Provisions
(a)
Where a Deemed-to-Satisfy Solution is proposed, Performance Requirements to are satisfied by complying with—
(i)
F4.1
to F4.12; and
(ii)
for farm buildings and farm sheds, Part H3.
(b)…
/editions/2019-a1/ncc-2019-volume-three-amendment-1/section-governing-requirements/part-a6-building
Introduction to this Part
The NCC groups buildings and structures by the purpose for which they are designed, constructed or adapted to be used, rather than by the function or use they are put to, assigning each type of building or structure with a…